Car Seat Blanket

I know some may be concerned about safety while using a type of blanket in a car seat. I did some reading up on car seat safety before posting this. Seriously? I think some have taken it a little too far. Some sites went as far as saying that you should buckle your child into their car seat without their jackets on, then put their jacket on backwards after they are buckled up. I understand that you want your child to be safe while riding in the car. And that you want the buckles to be as close to their bodies as possible so if, in a collision they are as secure as possible. Got it.

I felt that living in extreme temperatures that Alaska can have, my child being warm is just as important. I found that blankets are a must when the weather is cold.  Let me tell you when your in the grocery store for about an hour and the weather is below -20, the car cools off fast. 

So I'll let you decide on your child's safety and I'll decide on the safety of my mine. 

Last year black Friday shopping I picked up this fleece with the intent of making car seat blankets. And never got around to making them.

 So while our weather is fairly warm at the moment, and knowing we have many more months of winter. I decided it was time to dig out the fabric and make them. 

 I searched online for a nice, already done tutorial but couldn't find one that I liked. So I took some pictures of how I made mine. 

Step 1: cut fabric. For a toddler seat you'll need just under 1 1/2 yards of fleece. 

So I don't have a perfect pattern for you, just some measurements to go off of, you'll have to wing it a little bit.

Step 2: Open up you fabric and put it inside your car seat. I marked the top of mine with a pin before I opened mine up. Smooth it all flat and feel for where the buckles are at. Grab a pen and draw a line where each buckle is. I had 5 total. 

Step 3: Take a pair of sharp scissors and cut along your pen lines. These cut only have to be about 1 1/2". Also on each end make 2 smaller cuts, sort of at an angle. Don't make them very big. Only about 1/4". You are wanting to create 4 small sides to you cut. Repeat 4 more times. 

Step 4: Flip your fabric over. Tuck each of the small flap to your opening under and top stitch around the opening. Repeat 4 more times. 

You now should have something like this:

Step 5: I added a piece of elastic on the top to hold it from falling into the car seat. If you want to do this also, put your fabric back into your car seat. Put a small pin to mark where the elastic should be on each side. 

Step 6: Sew on your bias tape. I used 2 packages. I pieced the bias tape before sewing it to my fabric.

I was determined not to have to go out and buy anything for this project, and use what I had on hand. Each of blanket have 2 different colors. 

You want to start sewing so that your elastic is added at the end. When looking at your piece, the top is up, start  just below the pin on the right hand side.

 When you come to your 1st pin tuck the elastic into the bias tape. It will be underneath your fabric if your top is up. I back stitched over mine to make sure it wouldn't come undone with the extra force that I'm sure will be added to it. Now make sure you don't catch the elastic when your sewing to your next pin. 

When you get to you next pin, put your needle down. Find the other end of your elastic and tuck it into the bias tape, back stitch. 

Step 7: Finishing off. To finish off I stopped about 6 inches before I started. Put your needle down. Open up your bias tape and tuck the cut end in about 1 inch. Then fold your bias tape back together. This way all your raw edges are not exposed.

Finished car seat blanket!

Happy girl excited about her new blanket.

All bundled up.

The 2nd seat I have is slightly different is style. I had to add two pieces of elastic for this one.

2nd happy girl who loves her blanket and likes to haul her blanket every where! 

Now I'm a happy mom who doesn't have to haul blankets in and out of the house to car. This will cut down a lot on the laundry! I'm forever washing blankets that slip off and boots that drip on them. 

DIY Cupcake liners flower

I saw a picture of these cupcake liners made into flowers and knew right away

 I wanted to try make them.

So I started digging to see what kind of liners I had.

My color selection didn't come near to how cute the ones I saw were.  

You will need 7 cupcake liners.

1. Take and flatten 4 liners and glue centers together. Make little snips all the way around the circle.(Only cut the side of the linear. Don't cut into the center.)

2. Place the 5th cupcake liner (don't flatten this one) into the center and glued down.

3. Take liners 6 & 7 and cut center out. I also trimmed the edges down also. Roll these 2 together to form center of flower. Glue down. I used 3 in 1 glue to glue  center. Hot glue will also work.

4. Crunch and fluff the edges.

I like how it is a chunky full flower, with items you would have at home.

The 2nd one I did had a foil lining. It didn't lay as nice and was harder to get it to

fluff up the way the 1st one did. But I do think it was a lot cuter.

Then, of course, I had to make cards to put them on.

DIY Triangular Paper Tree

To create a triangular tree:
1. cut a 5 inch octagon.
You can cut this on cricut or silhouette or your paper cutter. If you are using your paper cutter follow steps 2 thru 4. If you can cut an octagon on your cricut or silhouette skip to step 5.

2. Measure and mark 1 ½ inches from each corner.

3. Draw a diagonal line to connect each mark.

4. Cut along each diagonal line to create an octagon

5. Cut octagon in half, then half and half again until you have 8 perfect triangular pieces.

If you are making your Christmas cards this year with trees on them this is a simple way to create a lot of perfect looking trees without all the cutting.